簡體 繁體 english menu
  • ABOUT
  • Products
    • Home Installation
      • Multi-Room Amplifier
      • Power Amplifier
      • Controller
      • Media Player
      • Volume Control
      • Power Management
      • 2.4G Wireless System
      • Solution Boxes
      • Speaker Selector
      • Speaker
    • Intelligent Conference
      • Two Channel Power Amplifier
      • Integrated Controller
      • Four Channel Power Amplifier
      • Professional DSP Karaoke Amplifier
      • Power Amplifier w/Dante Interface
      • Console Mixer W/Digital Effects
      • Sixteen Channel Digital Rack Mixer
      • 8CH Mixer W/Digital Effects
      • USB/TF MEDIA PLAYER w/RECORDING
      • Digital Audio Matrix
      • Digital Speaker Management
      • Professional Karaoke Processor
      • Digital Feedback Eliminator
      • Power Controller
      • Power Controller
      • DC Power Distribution
      • Dante Box - Line Input
      • Broadcast Conference Microphone
      • Wireless Conference Microphone
      • Conference Speaker
      • Full Range Speaker
      • Professional Subwoofer
      • Coaxial Monitor Speaker
      • Line Array Loudspeaker
      • Line Array Subwoofer
    • Pro Audio
      • Mixer
      • Headphone Amplifier
      • Guitar Tool
      • Mini Mixer
      • Direct Box
      • Mic Preamp
      • Phantom Power Supplier
      • Other Solution
    • Public Address
      • Amplifier
      • Speaker Selector
      • CSP Transceivers
      • CSP Receivers
      • Solution Boxes
      • Matching Transformer
      • Professional Meeting Microphone
  • NEWS
  • SERVICES
  • CONTACT
PLA2DI





Power Amplifier w/Dante Interface




PLA2DI


Power Amplifier w/Dante Interface

Multimedia conference room, Multifunction hall, Shopping mall, School, etc

Features

•Two Channels Model – 120W RMS.
•Stereo into 4-8 Ohm loads.
•Bridgeable for 70V or 100V (Direct Drive)
•Slot card for Dante Receiver.
•Power down after ~15 minutes of no signal and comply with Energy Star Power consumption limits of < 0.5W in standby.
•Yellow LED ( Front Panel) to indicated Standby mode is active.
•Terminal Block analog audio inputs on 2 CH amp.
•2 x amplifier outputs, bridgeable to 1 channel.
•Volume, Auto on/off signal sensing.
•Natural cooling without Fan.
•TRIGGER could be external remoting ON/OFF.
•Short circuit protection.
•Overheating protection.

Specifications

Output Power:

120W x 2, 8 Ω (31 V) RMS @ < 1 % THD+N

120W x 2, 4Ω (22 V) RMS @ < 1 % THD+N

240W, 70V @ < 1 % THD+N

240W, 100V @ < 1 % THD+N

Frequency Response: 20Hz~20KHz, +/- 2 dB @ 4Ω Load

S/N:>90dB  @ 1W(20 Hz - 20 kHz)

Input Sensitivity: 1.0V (+2.2dBu) @ Max Output 4Ω

Gain: 25 dB @ 4Ω

Input Impedance: >10K Ohm, Balanced

Maximum Input Level: 12.3 V (+24 dBu)

Trigger In/Out: DC 12V

High Pass Filter: 80 Hz(±2dB)

Input Connector: 5 pin Euro terminal

Trigger Connectors: 3.5 mm Jacks

Output Connectors:

4 pin Euro terminal (4Ω/8Ω) 

2 pin Euro terminal (70V/100V)                    

Power Requirements: 100 - 240 VAC, 50 - 60 Hz, 350W

Dimensions: 214mm x 249.8mm x 44mm (WxDxH)        

Weight: 1.94 Kg

 

Dante Audio Interface

2x2 audio channels

I2S digital audio format

16, 24 or 32-bit audio samples (per device or per channel)

44.1 KHz, 48KHz, 88.2KHz and 96KHz sample rates

 

Network Interface

Standard 100Mbps Ethernet

RMII Ethernet interface with MDIO

Hardware time-stamping, supporting sample-accurate playback

Transmit flows: 2 (unicast or multicast)

Receive flows: 2 (unicast or multicast)

Latency from 2ms

Documents